粉丝42获赞255
今天和大家聊一下硅铜密封胶在建筑应用中的常见的一个问题的解答。第一个问题,酸性硅铜胶和中性硅铜胶的使用有什么限制?酸性硅铜胶不能用以 金属、镀膜、玻璃,包括镜面、水泥面、石材等材料的表面,否则会导致材料表面生锈、氧化或腐蚀,造成污染或粘接失效。 那中性的硅铜胶呢?不宜在高温中啊,环境下使用,固化过程中会释放出啊甲虫气体,容易产生气泡。那中性啊,这个硅铜胶也不能长期进水的环境中使用,比如说鱼缸的粘接啊,用到 酸性胶窝形有机啊,这个硅铜胶不能用于铜切锌的金属表面,否则会导致材料表面生锈、氧化、腐蚀,形成污染啊,或者是粘接失效。第二个问题,为什么硅铜密封胶粉 化、开裂或收缩明显?这个如果质量比较差的贵铜浆中掺入过多的这个白油的劣质原料啊,固化后容易出现粉化、开裂或这个胶体收缩的现象。 第三个,硅铜密灰胶为什么会发黄或变色啊?比如说三元一柄橡胶、 epdm、 绿顶橡胶、沥青等原料与硅铜胶不相融啊,导致发黄和变色。 第二种情况,酸碱物质,如某些清洗剂、水泥浆的腐蚀性物质,容易导致硅农胶的变色。第三种情况,窝型的硅农胶在酸性环境中容易变色 啊,所以说啊,在施工以前必须要做一个相融性试验啊,试验合格后才能够啊,正常的使用硅铜胶。第四个问题,彩色硅铜胶为什么会掉色?那这个彩色硅铜密封胶主要用的是无机啊,或是有机的盐 料啊,作为一个着色剂,那无机颜料的话,颜色少,但是耐候性比较好,不容易褪色。有机颜料啊,颜色比较丰富,但但是他耐候性差啊,容易褪色。第五个问题, 为什么密封胶粘接不合格啊啊?两个原因,第一个密封胶不粘啊,在机体的本身上啊,这个不容易粘接。第二个是施工不规范,如果,如果基材表面不干净,养护环境或者养护时间不符合要求啊,未按规定啊,使用底图 或者是双组缝啊,这个比例不当的,都会造成这个粘接啊,不合格。第六个问题,硅农密封胶接缝旗鼓主要原因在哪里?第一个原因,施工不规范,特别是所用的这个电管 过宽,超过这个胶缝的宽度,施工时将电杆压入变形,导致这个涂硅胶后这个胶体鼓起。第二个原因是木墙板过大,结缝位移大,造成胶体受压啊,这个骨罩。第三个原因, 施工过程中温湿度变化太大,昼夜温差较大时啊,硅铜胶容易导致这个起鼓的现象。第七个问题,硅铜密封胶起泡的主要原因是什么啊?第一个原因啊,涂胶时带气啊,这个溶密封胶的连续性和均匀性没有掌握好的话,或反复修胶时容易。 第二个原因,涂密封胶前不保证接口或附件材料按要求干燥啊,比如说支撑感潮湿,水分会渗入密封胶条而并产生气泡。 第三个原因是福建释放气体,比如说啊,这个支撑杆啊,这个闭孔破裂,导致这个呃脱气啊,产生的气泡。那第四个原因是基材表面温度过高,导致密封胶表面快速固化啊,释放的小分子气体不能及时排除导致的这个气泡。 第五个原因是硅铜密封胶与某些材料发生一些反应,如碱性混凝土和水泥与混凝土发生反应,就会产生一些气泡。第八个问题,硅铜密封胶接缝 粪开裂的主要原因有哪些?第一个原因是硅铜胶选用不当,这个选用的喂音能力达不到相应的一个喂音等级的要求。第二个原因是啊,密封胶这个缝啊选用啊设计不合理,如啊,密封胶缝过宽,导致密封胶难以涂抹,密封不到位的。 第三个原因是木墙板安装位移偏差过大。第四个原因是密封胶未完全固化前接缝位移过大。第五个原因,密封胶三面粘合位移能力啊有限。第六个原因,硅胶厚度太薄,导致密封胶损坏或粘结失效。第九个问题,石材污染的原因是什么? 由于石材是一种多孔性的一些材料,如果硅铜胶中有挥发性的油性物质的,就会造造成这个石材的污染。第十个问题,中空玻璃密封胶失效的主要原因是什么呢?第一个原因啊,丁基胶可能与硅铜胶不相容。第二个是啊,密封胶条啊,这个这硅铜的啊,二次密封啊,这个里面有矿物油,导致 这个啊出现的问题啊。第三个是这个,呃,这个密封条啊,与这个填充矿物油油的啊,硅铜密封胶接触了啊,产生的一些呃,这个实效 啊,比如说和木墙内厚呃,硅铜或者门窗密封胶啊接触也会产生这些问题。第四个原因是干燥剂或加工工艺的因素造成的。以上就是啊建筑硅铜密封胶使用过程中的十大问题。
硅铜密封胶和聚安子密封胶两者的区别?硅铜密封胶和聚安子密封胶第一区别就是主要原材料上的区别。硅铜胶的主要成分有聚二甲基硅氧碗, 聚氨酯胶的主要成分为多元益氢酸酯和多元醇。由于供氧件件能大于碳氮件和 太阳舰,所以硅铜胶在理论上耐紫外线能力强于聚氨酯胶,这个可以通过紫外线照射试验箱来检验。硅铜胶和聚氨酯胶放入紫外线箱照射或者是高温烘烤二百四十小时,聚氨酯胶会有明显的黄变,七百二十小时以上,聚氨酯胶就会有表面粉化现象。 当然不能说所有的硅铜胶耐候性都比聚氨酯密封胶好,还是要看密封产品的品质。下一期我们来分享硅铜密封胶和聚氨酯胶适合用的领域和各自的优势。